? coilcraft, inc. 2010 specifications subject to change without notice. please check our website for latest information. chip inductors - 0402hp series (1005) document 526 -1 document 526-1 revised 10/15/10 ? higher q and lower dcr than other 0402 inductors ? very high srf values ? as high as 16 ghz ? excellent current handling capability ? up to 2300 ma ? 52 inductance values from 1.0 to 220 nh core material ceramic terminations rohs compliant silver-palladium-platinum-glass frit. other terminations available at additional cost. weight 0.7 ? 1.0 mg ambient temperature ?40c to +125c with i rms current, +125c to +140c with derated current storage temperature component: ?40c to +140c. packaging: ?40c to +80c resistance to soldering heat max three 40 second reflows at +260c, parts cooled to room temperature between cycles temperature coefficient of inductance (tcl) +25 to +125 ppm/c moisture sensitivity level (msl) 1 (unlimited floor life at <30c / 85% relative humidity) failures in time (fit) / mean time between failures (mtbf) one per billion hours / one billion hours, calculated per telcordia sr-332 packaging 2000 per 7 reel. paper tape: 8 mm wide, 0.66 mm thick, 2 mm pocket spacing pcb washing only pure water or alcohol recommended 0 60 50 40 30 20 10 70 80 inductance (nh) 1 10 100 1000 10000 frequency (mhz) 51 nh 39 nh 27 nh 11 nh 2.0 nh 68 nh typical l vs frequency 0 60 50 40 30 20 10 70 80 90 100 110 120 q factor 1 10 100 1000 10000 frequency (mhz) 68 nh 51 nh 39 nh 27 nh 11 nh 2.0 nh typical q vs frequency current derating -40 -20 0 20 40 60 80 100 140 120 ambient temperature (c) 120 110 100 90 80 70 60 50 40 30 20 10 0 percent of rated rms i 25c a b overall c d j f f g h recommended land pattern e terminal terminal wraparound: approx 0.007/0,18 both ends i i pick and place material de fgh i j 0.010 0.020 0.008 0.024 0.026 0.014 0.020 inches 0,25 0,51 0,20 0,61 0,66 0,36 0,51 mm a max b (min ? max) c max 0.043 0.020 ? 0.028 0.024 inches 1,09 0,51 ? 0,71 0,61 mm 0402hp a max b c max 0.044 0.026 0.002 0.026 inches 1,12 0,66 0,051 0,66 mm 0402hph
? coilcraft, inc. 2010 0402hp series (1005) specifications subject to change without notice. please check our website for latest information. document 526-2 document 526-2 revised 10/15/10 inductance 2 percent test freq 900 mhz 1.7 ghz srf typ 5 dcr max 6 i rms 7 part number 1 (nh) tolerance 3 (mhz) l typ q typ 4 l typ q typ 4 (ghz) (ohms) (ma) 0402hp-1n0xjl_ 1.0 5 250 0.97 46 0.99 72 16.0 0.030 2300 0402hp-2n0xjl_ 2.0 5 250 1.96 58 1.98 85 15.2 0.038 2100 0402hp-2n2xjl_ 2.2 5 250 2.17 60 2.17 86 15.1 0.038 2100 0402hp-2n4x_l_ 2.4 5,2 250 2.37 60 2.38 83 14.0 0.042 2000 0402hp-2n7x_l_ 2.7 5,2 250 2.66 62 2.68 85 13.0 0.056 1500 0402hp-3n3x_l_ 3.3 5,2 250 3.26 66 3.28 95 12.8 0.045 1700 0402hp-3n6x_l_ 3.6 5,2 250 3.56 65 3.58 94 11.7 0.045 1700 0402hp-3n9x_l_ 3.9 5,2 250 3.87 64 3.91 98 9.50 0.045 1700 0402hp-4n3x_l_ 4.3 5,2 250 4.26 63 4.33 90 7.15 0.040 1600 0402hp-4n7x_l_ 4.7 5,2 250 4.67 58 4.74 83 6.85 0.060 1500 0402hp-5n1x_l_ 5.1 5,2 250 5.07 54 5.16 76 6.80 0.100 1200 0402hp-5n6x_l_ 5.6 5,2 250 5.56 73 5.66 105 6.50 0.048 1600 0402hp-6n2x_l_ 6.2 5,2 250 6.18 73 6.25 100 5.80 0.050 1600 0402hp-6n8x_l_ 6.8 5,2 250 6.78 68 6.97 94 5.80 0.055 1500 0402hp-7n5x_l_ 7.5 5,2 250 7.49 60 7.77 82 5.40 0.080 1400 0402hp-8n2x_l_ 8.2 5,2 250 8.10 68 8.40 95 5.40 0.054 1500 0402hp-8n7x_l_ 8.7 5,2 250 8.73 66 9.04 95 5.00 0.058 1500 0402hp-9n0x_l_ 9.0 5,2 250 8.99 67 9.21 92 5.00 0.070 1400 0402hp-9n5x_l_ 9.5 5,2 250 9.52 64 9.97 90 4.70 0.075 1400 0402hp-10nx_l_ 10 5,2 250 9.98 62 10.4 90 4.70 0.085 1300 0402hp-11nx_l_ 11 5,2 250 11.0 68 11.6 98 4.70 0.065 1400 0402hp-12nx_l_ 12 5,2 250 12.0 66 12.6 100 4.40 0.070 1200 0402hp-13nx_l_ 13 5,2 250 13.1 62 13.9 82 4.20 0.140 870 0402hp-15nx_l_ 15 5,2 250 15.1 62 16.0 85 3.90 0.078 1100 0402hp-16nx_l_ 16 5,2 250 16.2 57 17.3 77 3.70 0.130 850 0402hp-18nx_l_ 18 5,2 250 18.2 58 19.5 74 3.55 0.120 900 0402hp-19nx_l_ 19 5,2 250 19.2 61 20.7 88 3.50 0.145 850 0402hp-20nx_l_ 20 5,2 250 20.3 58 22.0 76 3.50 0.155 780 0402hp-21nx_l_ 21 5,2 250 21.3 48 23.2 62 1.70 0.460 450 0402hp-22nx_l_ 22 5,2 250 22.3 60 24.4 74 3.30 0.160 800 0402hp-23nx_l_ 23 5,2 250 23.3 60 25.5 77 3.30 0.160 800 0402hp-24nx_l_ 24 5,2 250 24.5 55 27.1 71 3.15 0.170 700 0402hp-25nx_l_ 25 5,2 250 25.5 57 28.3 73 3.15 0.250 700 0402hp-26nx_l_ 26 5,2 250 26.6 56 29.3 74 3.15 0.275 700 0402hp-27nx_l_ 27 5,2 250 27.3 62 29.5 86 3.20 0.330 450 0402hp-30nx_l_ 30 5,2 250 30.8 61 35.0 87 2.90 0.330 450 0402hp-33nx_l_ 33 5,2 250 34.0 61 38.3 80 2.80 0.330 490 0402hp-36nx_l_ 36 5,2 250 37.1 59 42.2 76 2.80 0.360 480 0402hp-37nx_l_ 37 5,2 250 38.2 57 44.0 72 2.70 0.480 470 0402hp-39nx_l_ 39 5,2 250 40.5 56 47.0 84 2.60 0.430 450 0402hp-40nx_l_ 40 5,2 250 41.3 56 47.4 75 2.60 0.430 450 0402hp-43nx_l_ 43 5,2 250 45.0 52 54.1 68 2.50 0.520 450 0402hp-47nx_l_ 47 5,2 250 49.0 48 58.9 62 2.40 0.580 420 0402hp-51nx_l_ 51 5,2 250 49.1 52 58.8 59 2.30 0.700 360 0402hph-56nx_l_ 56 5,2 250 58.8 56 72.2 64 2.07 0.900 330 0402hph-68nx_l_ 68 5,2 250 72.2 56 91.4 64 1.84 1.00 320 0402hph-82nx_l_ 82 5,2 250 89.7 52 ? ? 1.75 1.10 315 0402hph-r10x_l_ 100 5,2 250 ? ? ? ? 1.58 1.20 310 0402hph-r12x_l_ 120 5,2 250 ? ? ? ? 1.25 1.20 310 0402hph-r15x_l_ 150 5,2 100 ? ? ? ? 1.14 2.0 240 0402hph-r18x_l_ 180 5,2 100 ? ? ? ? 1.08 2.1 240 0402hph-r22x_l_ 220 5,2 100 ? ? ? ? 0.96 3.1 160 1. when ordering, specify tolerance , termination and packaging codes: 0402hp-82nx jlw tolerance: g = 2% j = 5% (table shows stock tolerances in bold.) termination: l = rohs compliant silver-palladium-platinum-glass frit. special order: t = rohs tin-silver-copper (95.5/4/0.5) or s = non-rohs tin-lead (63/37). packaging: w =7 machine-ready reel. eia-481 punched paper tape (2000 parts per full reel). u = less than full reel. in tape, but not machine ready. to have a leader and trailer added ($25 charge), use code letter w instead. 2. inductance measured at test frequency using a coilcraft smd-f fixture in an agilent/hp 4286 impedance analyzer with coilcraft-provided correlation pieces. 3. tolerances in bold are stocked for immediate shipment. 4. q measured using an agilent/hp 4287a with an agilent/hp 16197 test fixture. 5. srf measured using an agilent/hp 8722es network analyzer and a coilcraft smd-d test fixture. 6. dcr measured on a micro-ohmmeter and a coilcraft ccf858 test fixture. 7. current that causes a 15c temperature rise from 25c ambient. 8. electrical specifications at 25c. refer to doc 362 ?soldering surface mount components? before soldering. designer?s kits c403a and b contain 20 each of 5% values designer?s kits c403a-2 and b-2 contain 20 each of 2% values
|
